Welcome to our new forum
All users of the legacy CODESYS Forums, please create a new account at account.codesys.com. But make sure to use the same E-Mail address as in the old Forum. Then your posts will be matched.
Close
Dear sirs,
I had a problem installing codesys release 2.2.0.1 on Raspberry PI 2.
CODESYS version on PC : V3.5 SP7 patch 1 RASPIAN image : Wheezy 05-05-2015 CODESYS Control for Raspberry : ver. 2.2.0.1
I've applied exactly the instructions in the paper .
**PROBLEM ** : After Raspberry PI 2 startup, linux loads and Codesys starts but after few seconds the Codesyscontrol process shuts down.
DIAGNOSTIC : As you can see in the picture, the process shuts down after few seconds.
At the end of the LOG file I've attached an error is signaled but I'm not able to correct it.
After many tests I've found when the problem is created.
If you install the Raspbian OS wheezy 05-05-2015without updates and CodeSys runtime everything runs ok.
After the upgrade ( from internet by using sudo apt-get dist-upgrade ) codesyscontrol shuts down in a few seconds ( look at the picture in the previous post ).
Something incompatible with new updates
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
Hi,
yes at the moment only the standard image works (without doing an update)
We have an V3.5.6.10 Runtime for it but is not released.
hope this will be done a.s.a.p.
I've send you additional an pm.
BR
Edwin
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
If you want to use CODESYS with Raspberry Touch LCD 7":
Update to 4.0.9
Download start.elf and fixup.dat from latest firmware and replace these boot partition.
I hope, that's help you.
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
Dear sirs,
I had a problem installing codesys release 2.2.0.1 on Raspberry PI 2.
CODESYS version on PC : V3.5 SP7 patch 1
RASPIAN image : Wheezy 05-05-2015
CODESYS Control for Raspberry : ver. 2.2.0.1
I've applied exactly the instructions in the paper .
**PROBLEM ** : After Raspberry PI 2 startup, linux loads and Codesys starts but after few seconds the Codesyscontrol process shuts down.
DIAGNOSTIC : As you can see in the picture, the process shuts down after few seconds.
At the end of the LOG file I've attached an error is signaled but I'm not able to correct it.
Could you kindly help me.
Thanks a lot.
FINAL PART OF THE LOG FILE!
COMPLETE LOG FILE
codesyscontrol.txt [19.22 KiB]
NEWS
After many tests I've found when the problem is created.
If you install the Raspbian OS wheezy 05-05-2015 without updates and CodeSys runtime everything runs ok.
After the upgrade ( from internet by using sudo apt-get dist-upgrade ) codesyscontrol shuts down in a few seconds ( look at the picture in the previous post ).
Something incompatible with new updates
Hi,
yes at the moment only the standard image works (without doing an update)
We have an V3.5.6.10 Runtime for it but is not released.
hope this will be done a.s.a.p.
I've send you additional an pm.
BR
Edwin
Thank you very much for your support.
Best regards.
When is this getting fixed? The update has to happen to fix other Pi issues, so if running latest Raspbian, your dead in the water.
Hi,
scheduled for this week and on the way...
BR
Edwin
Hello,
I'm testing CODESYS for RaspberryPi too. I'm using Raspberry Pi 2.
Latest kernel (and RaspberryPi firmware) for CODESYS which works is 4.0.9 (https://github.com/Hexxeh/rpi-firmware/commit/46d179597370c5145c7452796acbee0f1ff93392)
For update (downgrade) to this version use:
Raspberry Pi firmware list with change notes is available at https://github.com/Hexxeh/rpi-firmware/commits/master
If you want to use CODESYS with Raspberry Touch LCD 7":
Update to 4.0.9
Download start.elf and fixup.dat from latest firmware and replace these boot partition.
I hope, that's help you.