CODESYS - the IEC 61131-3 automation software
https://forum.codesys.com/

CODESYS Control for PFC100 SL, Error while installing package
https://forum.codesys.com/viewtopic.php?f=20&t=9110
Page 1 of 1

Author:  kimao [ Wed Sep 05, 2018 1:58 pm ]
Post subject:  CODESYS Control for PFC100 SL, Error while installing package

Hello

Trying to install the CODESYS Control for PFC100 SL i get error messages. Anyone know what could be the problem/solution?

Author:  Edwin Schwellinger [ Sun Sep 09, 2018 6:58 am ]
Post subject:  Re: CODESYS Control for PFC100 SL, Error while installing package

Hi,
never seen, which firmware is this,what happens if you install it by login by ssh and:
ipkg install codesyscontrol_arm_pfc200_V3.5.13.x.ipk

BR
Edwin

Author:  kimao [ Thu Sep 13, 2018 10:33 am ]
Post subject:  Re: CODESYS Control for PFC100 SL, Error while installing package

Hello
I am using this package: codesyscontrol_arm_pfc100_V3.5.12.40.ipk

Using ssh I get the same error:

root@PFC100-416D28:~ ipkg install codesyscontrol_arm_pfc100_V3.5.12.40.ipk
ipkg: *** Couldnt kill old gunzip process *** aborting

If I log into the web interface of the PLC I get the 3S interface and not the wago Interface, It seems like it might be installed.

If I scan for PFC100 in the PFC100 phane in codesys I find it.
If I scan for the device in my project i don't find it.
If i try to start the Runtime using the start button in the PFC100 phane in codesys I get an error message..

See attached photos.

Author:  Edwin Schwellinger [ Thu Sep 13, 2018 2:52 pm ]
Post subject:  Re: CODESYS Control for PFC100 SL, Error while installing package

Hi,
Installation is ok,
just add a Gateway with the IP of the PFC100. Switch to this new Gateway, then you will find the PFC100 by the scan.

BR
Edwin

Author:  kimao [ Fri Sep 21, 2018 10:56 am ]
Post subject:  Re: CODESYS Control for PFC100 SL, Error while installing package

Hello, thank you for the reply.

Adding a gateway with the IP of the PLC does not help. I get this error message.

Author:  Edwin Schwellinger [ Sat Sep 22, 2018 6:14 am ]
Post subject:  Re: CODESYS Control for PFC100 SL, Error while installing package

Hi,
could you Login by ssh (putty for example) and call
top

or
cat /tmp/codesyscontrol.log
to chek if the runtime is running?

BR
Edwin

Author:  kimao [ Tue Sep 25, 2018 1:32 pm ]
Post subject:  Re: CODESYS Control for PFC100 SL, Error while installing package

Hello
codesyscontrol.log is not found,

Author:  Edwin Schwellinger [ Tue Sep 25, 2018 3:02 pm ]
Post subject:  Re: CODESYS Control for PFC100 SL, Error while installing package

Hi,
your screenshot say you are using Firmware(09) Version,
I would update to current Version ( request on Wago homepage for the new Firmware 11)
Boot with it from micro sd and update your Firmware by WBM in the browser...

BR
Edwin

Page 1 of 1 All times are UTC+01:00
Powered by phpBB® Forum Software © phpBB Limited
https://www.phpbb.com/