Author |
Message |
kimao
|
PostPosted: Wed Sep 05, 2018 1:58 pm |
|
Joined: Fri Aug 03, 2012 2:00 pm Posts: 11
|
Hello
Trying to install the CODESYS Control for PFC100 SL i get error messages. Anyone know what could be the problem/solution?
You do not have the required permissions to view the files attached to this post.
|
|
Top |
|
 |
Edwin Schwellinger
|
PostPosted: Sun Sep 09, 2018 6:58 am |
|
Joined: Mon Sep 05, 2005 9:42 am Posts: 3570
|
Hi, never seen, which firmware is this,what happens if you install it by login by ssh and: ipkg install codesyscontrol_arm_pfc200_V3.5.13.x.ipk
BR Edwin
|
|
Top |
|
 |
kimao
|
PostPosted: Thu Sep 13, 2018 10:33 am |
|
Joined: Fri Aug 03, 2012 2:00 pm Posts: 11
|
Hello I am using this package: codesyscontrol_arm_pfc100_V3.5.12.40.ipk
Using ssh I get the same error:
root@PFC100-416D28:~ ipkg install codesyscontrol_arm_pfc100_V3.5.12.40.ipk ipkg: *** Couldnt kill old gunzip process *** aborting
If I log into the web interface of the PLC I get the 3S interface and not the wago Interface, It seems like it might be installed.
If I scan for PFC100 in the PFC100 phane in codesys I find it. If I scan for the device in my project i don't find it. If i try to start the Runtime using the start button in the PFC100 phane in codesys I get an error message..
See attached photos.
You do not have the required permissions to view the files attached to this post.
|
|
Top |
|
 |
Edwin Schwellinger
|
PostPosted: Thu Sep 13, 2018 2:52 pm |
|
Joined: Mon Sep 05, 2005 9:42 am Posts: 3570
|
Hi, Installation is ok, just add a Gateway with the IP of the PFC100. Switch to this new Gateway, then you will find the PFC100 by the scan.
BR Edwin
You do not have the required permissions to view the files attached to this post.
|
|
Top |
|
 |
kimao
|
PostPosted: Fri Sep 21, 2018 10:56 am |
|
Joined: Fri Aug 03, 2012 2:00 pm Posts: 11
|
Hello, thank you for the reply.
Adding a gateway with the IP of the PLC does not help. I get this error message.
You do not have the required permissions to view the files attached to this post.
|
|
Top |
|
 |
Edwin Schwellinger
|
PostPosted: Sat Sep 22, 2018 6:14 am |
|
Joined: Mon Sep 05, 2005 9:42 am Posts: 3570
|
Hi, could you Login by ssh (putty for example) and call top
or cat /tmp/codesyscontrol.log to chek if the runtime is running?
BR Edwin
|
|
Top |
|
 |
kimao
|
PostPosted: Tue Sep 25, 2018 1:32 pm |
|
Joined: Fri Aug 03, 2012 2:00 pm Posts: 11
|
Hello codesyscontrol.log is not found,
You do not have the required permissions to view the files attached to this post.
|
|
Top |
|
 |
Edwin Schwellinger
|
PostPosted: Tue Sep 25, 2018 3:02 pm |
|
Joined: Mon Sep 05, 2005 9:42 am Posts: 3570
|
Hi, your screenshot say you are using Firmware(09) Version, I would update to current Version ( request on Wago homepage for the new Firmware 11) Boot with it from micro sd and update your Firmware by WBM in the browser...
BR Edwin
|
|
Top |
|
 |