CODESYS - the IEC 61131-3 automation software

Welcome to the official CODESYS Forum
Deutsche Version English version russian version 
It is currently Thu Aug 24, 2017 3:56 am

All times are UTC+01:00




Post new topic  Reply to topic  [ 6 posts ] 
Author Message
PostPosted: Wed Jan 11, 2017 8:06 pm 
Offline

Joined: Wed Jan 11, 2017 5:45 pm
Posts: 5
Hello!
I am trying to etablish a connection to a Rexroth RC6_9_20 with Bodas Design 3.0.17.
I want to read out the program from the RC, and save it on my Computer
Could someone please tell me if there is a kind of tutorial here at this forum how to set this up?
Here is what I do:
File - Open - Open project from PLC - PLC - Target Setting _ RC6-9 20 Standard V1.9 - Interface - Peak PCAN-USB - Devicetype RC4-6/22 - Scan

I cannot connect, any ideas what`s wrong?

Thanks in advance !
Newbe


Top
   
PostPosted: Thu Jan 12, 2017 12:49 pm 
Offline
Frequent User
Frequent User

Joined: Thu Jun 14, 2007 9:49 am
Posts: 974
The project must be saved on the device, otherwise it is impossible to open it.
a program is compiled in the PC and send to the PLC as a machinelanguage, so you can not download from the device as a compiled file is unreadable (for the most people)

_________________
shooter@home.nl
computer shooter
paul deelen
jacob van wassenaerstraat 29
NL 5224 GG 's-Hertogenbosch
skype shooter paul.deelen
phone +31736139136


Top
   
PostPosted: Thu Jan 12, 2017 10:14 pm 
Offline

Joined: Wed Jan 11, 2017 5:45 pm
Posts: 5
Thanks for information!


Top
   
PostPosted: Fri Jan 13, 2017 9:56 pm 
Offline

Joined: Wed Jan 11, 2017 5:45 pm
Posts: 5
Ok, so I`ve been able to connect to the RC.
Used Bodas Service 3.5 to flash an existing HEX. file into the RC, and then downloaded a test program.
When opening Bodas design after doing a "rebuild all" I got a message "Not found HEX-File:C:\ xxx\xxxx"
Have I done something wrong here?
I could go online without problems.....


Top
   
PostPosted: Sun Jan 15, 2017 4:46 pm 
Offline
Frequent User
Frequent User

Joined: Thu Jun 14, 2007 9:49 am
Posts: 974
this is outside the scope of codesys,
however have a look at settings if the compiler makes a correct hex file and obvious where it is stored.
check the project directory.

_________________
shooter@home.nl
computer shooter
paul deelen
jacob van wassenaerstraat 29
NL 5224 GG 's-Hertogenbosch
skype shooter paul.deelen
phone +31736139136


Top
   
PostPosted: Sun Jan 15, 2017 9:16 pm 
Offline

Joined: Wed Jan 11, 2017 5:45 pm
Posts: 5
Thanks, I will try!


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 6 posts ] 

All times are UTC+01:00


Who is online

Users browsing this forum: No registered users and 5 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited