[ComponentManager]
Component.1=CmpTargetVisuStub
Component.2=CmpCodeMeter
Component.3=CmpWebServer
Component.4=CmpWebServerHandlerV3
Component.5=CmpPCANBasicDrv

[CmpSettings]
;SplitDatabases=0
FileReference.0=SysFileMap.cfg, SysFileMap

[CmpRouter]
;MaxRouters=1

[CmpBlkDrvCom]
;Example for a configuration of this block driver:
;EnableAutoAddressing=1 should be set to activate the
;Mainnet-Mainnet-Communication on serial line.
;Com.0.Port=1
;Com.0.Name=MyCom
;Com.0.Baudrate=115200
;Com.0.EnableAutoAddressing=1  

[CmpBlkDrvCanServer]
;Example for a configuration of this block driver:
;Interface name is always Canbus0.
;Example: Use in the CmpRouter section following entry '0.MainNet=Canbus0'
;0.Baudrate=250    ; Canbus Baudrate
;0.NetId=0  		; Canbus Network ID
;0.NodeId=10 		; NodeId of SDOServer

[CmpCAASdoServer]
;MaxSegmentsPerCycle=0 ; for block upload: maximum of sent segments per cycle; 0 means infinity

[CmpCAASdoClient]
;MaxSegmentsPerCycle=0 ; for block download: maximum of sent segments per cycle; 0 means infinity

[CmpRetain]
;Retain.SRAM.Size=0x200200
;Retain.SRAM.Address=0xFA3C5776
;SimulateSRAM=1

[CmpApp]
;Bootproject.CreateOnDownload=0
;Bootproject.StoreOnlyOnDownload=0
;Bootproject.InvalidateByRename=1
;Bootproject.InvalidateBySetting=1
;Bootproject.InvalidateNever=0
;PersistentForce=0
;RetainType.Applications=InSRAM
;RetainType.Applications=OnPowerfail
;RetainType.Applications=None
;Exception.Hardware.GlobalStop=1

[CmpSchedule]
;EnableLogger=1
;Timeslicing.Mode=Internal
;Timeslicing.PlcSlicePercent=80
;Timeslicing.PlcSliceUs=4000
;Timeslicing.StartOnProcessorLoad=1
;SchedulerPriority=5
;SchedulerInterval=1000
ProcessorLoad.Maximum=80

[SysFile]
;FilePath=D:/Temp/Default
;FilePath.1=./Boot, *.app, *.ap_, *.err, *.crc, *.ret, *.csv, *.frc
;FilePath.2=D:/Temp/Wildcards, *.txw
;FilePath.3=D:/Temp/Wildcards, File7.txt
;IecFilePath=D:/Temp/IEC

[SysProcess]
BasePriority=Realtime

[CmpLog]
;Logger.0.Name=PlcLog
;Logger.0.Filter=0xFFFFFFFF
;Logger.0.Enable=1
;Logger.0.MaxEntries=1000
;Logger.0.MaxFileSize=5000
;Logger.0.MaxFiles=3
;Logger.0.Backend.0.ClassId=0x0000010B   ;sends logger messages to SysOut
;Logger.0.Backend.1.ClassId=0x00000104   ;writes logger messages in a file
;Logger.0.Backend.2.ClassId=0x00000135   ;sends logger messages as UDP syslog
;Logger.0.Type=0x314   ;Set the timestamp to RTC
;Logger.1.Name=CommLog
;Logger.1.Enable=1

[IoDrvHilscher]
;IsaScanStartAddress=0xA0000
;IsaLookupSize=0x50000
;DisableIsaScan=1
;DisablePciScan=1
;VendorName=Hilscher GmbH
;DeviceName=CIF50-PB
;ModuleType=0x20	;This is a profibus master
;DeviceInfo=0x3236	;This is a CIF50-PB card
;Instance.0.VendorName=Hilscher GmbH
;Instance.0.DeviceName=CIF50-PB
;Instance.0.ModuleType=0x20	;This is a profibus master
;Instance.0.DeviceInfo=0x3236	;This is a CIF50-PB card
;Device.0.Address=0x12345678
;Device.0.Size=8192
;Pci.VendorId=0x10B5
;Pci.DeviceId=0x9050
;Pci.SubVendorId=0x10B5
;Pci.SubSystemId=0x1080

;[CmpDevice]
;TargetVersionMask=0xFFFF0000
;TargetVersionCompatibilityMask=0xFFFFFF00

[SysTarget]
;NodeNameUnicode="T\00e\00s\00t\00\00"
;NodeName="Test"

[SysTask]
;OSPriority.System.Base=0
;OSPriority.System.End=31
;OSPriority.Realtime.Base=32
;OSPriority.Realtime.End=63
;OSPriority.High.Base=64
;OSPriority.High.End=95
;OSPriority.AboveNormal.Base=96
;OSPriority.AboveNormal.End=127
;OSPriority.Normal.Base=128
;OSPriority.Normal.End=159
;OSPriority.BelowNormal.Base=160
;OSPriority.BelowNormal.End=191
;OSPriority.Low.Base=192
;OSPriority.Low.End=223
;OSPriority.Lowest.Base=224
;OSPriority.Lowest.End=255

[IoDrvCIFX]
;BackgroundDiag=1

[CmpHilscherCIFX]
;TraceLevel=0xffffffff
;InterruptMode=1
;DMAMode=1
;Device.0.BootloaderFilePath=.\HilscherCIFX\Firmware\NETX100-BSL.bin 
;Device.0.Channel.0.FirmwareFile=.\HilscherCIFX\Firmware\cifxcom.nxf
;Device.1.BootloaderFilePath=.\HilscherCIFX\Firmware\NETX100-BSL.bin 
;Device.1.Channel.0.FirmwareFile=.\HilscherCIFX\Firmware\cifxpnm.nxf
;Device.2.BootloaderFilePath=.\HilscherCIFX\Firmware\NETX100-BSL.bin 
;Device.2.Channel.0.FirmwareFile=.\HilscherCIFX\Firmware\cifxdpm.nxf

[CmpWebServer]
;The handling of startup/shutdown of the webserver:
;0->automatically start, shutdown only on shutdown of the runtime;1->automatically start, could be shutdown on demand
;2(default)->start/shutdown on demand;3->start on demand, shutdown only on shutdown of the runtime
;StartupType=2
;The TCP port the webserver listens on
;WebServerPortNr=8080

[CmpOPCUAServer]
;TraceEnabled=1
;TraceLevel=0x0028